diff --git a/drivers/video/anx9804.c b/drivers/video/anx9804.c
index 3037ff3..52b5988 100644
--- a/drivers/video/anx9804.c
+++ b/drivers/video/anx9804.c
@@ -21,18 +21,23 @@
  * This function will init an anx9804 parallel lcd to dp bridge chip
  * using the passed in parameters.
  *
- * @i2c_bus:	Number of the i2c bus to which the anx9804 is connected.
+ * @i2c_bus:	Device of the i2c bus to which the anx9804 is connected.
  * @lanes:	Number of displayport lanes to use
  * @data_rate:	Register value for the bandwidth reg 0x06: 1.62G, 0x0a: 2.7G
  * @bpp:	Bits per pixel, must be 18 or 24
  */
-void anx9804_init(unsigned int i2c_bus, u8 lanes, u8 data_rate, int bpp)
+void anx9804_init(struct udevice *i2c_bus, u8 lanes, u8 data_rate, int bpp)
 {
-	unsigned int orig_i2c_bus = i2c_get_bus_num();
-	u8 c, colordepth;
-	int i;
+	struct udevice *chip0, *chip1;
+	int c, colordepth, i, ret;
 
-	i2c_set_bus_num(i2c_bus);
+	ret = i2c_get_chip(i2c_bus, 0x38, 1, &chip0);
+	if (ret)
+		return;
+
+	ret = i2c_get_chip(i2c_bus, 0x39, 1, &chip1);
+	if (ret)
+		return;
 
 	if (bpp == 18)
 		colordepth = 0x00; /* 6 bit */
@@ -40,24 +45,23 @@
 		colordepth = 0x10; /* 8 bit */
 
 	/* Reset */
-	i2c_reg_write(0x39, ANX9804_RST_CTRL_REG, 1);
+	dm_i2c_reg_write(chip1, ANX9804_RST_CTRL_REG, 1);
 	mdelay(100);
-	i2c_reg_write(0x39, ANX9804_RST_CTRL_REG, 0);
+	dm_i2c_reg_write(chip1, ANX9804_RST_CTRL_REG, 0);
 
 	/* Write 0 to the powerdown reg (powerup everything) */
-	i2c_reg_write(0x39, ANX9804_POWERD_CTRL_REG, 0);
+	dm_i2c_reg_write(chip1, ANX9804_POWERD_CTRL_REG, 0);
 
-	c = i2c_reg_read(0x39, ANX9804_DEV_IDH_REG);
+	c = dm_i2c_reg_read(chip1, ANX9804_DEV_IDH_REG);
 	if (c != 0x98) {
 		printf("Error anx9804 chipid mismatch\n");
-		i2c_set_bus_num(orig_i2c_bus);
 		return;
 	}
 
 	for (i = 0; i < 100; i++) {
-		c = i2c_reg_read(0x38, ANX9804_SYS_CTRL2_REG);
-		i2c_reg_write(0x38, ANX9804_SYS_CTRL2_REG, c);
-		c = i2c_reg_read(0x38, ANX9804_SYS_CTRL2_REG);
+		c = dm_i2c_reg_read(chip0, ANX9804_SYS_CTRL2_REG);
+		dm_i2c_reg_write(chip0, ANX9804_SYS_CTRL2_REG, c);
+		c = dm_i2c_reg_read(chip0, ANX9804_SYS_CTRL2_REG);
 		if ((c & ANX9804_SYS_CTRL2_CHA_STA) == 0)
 			break;
 
@@ -66,51 +70,51 @@
 	if (i == 100)
 		printf("Error anx9804 clock is not stable\n");
 
-	i2c_reg_write(0x39, ANX9804_VID_CTRL2_REG, colordepth);
+	dm_i2c_reg_write(chip1, ANX9804_VID_CTRL2_REG, colordepth);
 
 	/* Set a bunch of analog related register values */
-	i2c_reg_write(0x38, ANX9804_PLL_CTRL_REG, 0x07);
-	i2c_reg_write(0x39, ANX9804_PLL_FILTER_CTRL3, 0x19);
-	i2c_reg_write(0x39, ANX9804_PLL_CTRL3, 0xd9);
-	i2c_reg_write(0x39, ANX9804_RST_CTRL2_REG, ANX9804_RST_CTRL2_AC_MODE);
-	i2c_reg_write(0x39, ANX9804_ANALOG_DEBUG_REG1, 0xf0);
-	i2c_reg_write(0x39, ANX9804_ANALOG_DEBUG_REG3, 0x99);
-	i2c_reg_write(0x39, ANX9804_PLL_FILTER_CTRL1, 0x7b);
-	i2c_reg_write(0x38, ANX9804_LINK_DEBUG_REG, 0x30);
-	i2c_reg_write(0x39, ANX9804_PLL_FILTER_CTRL, 0x06);
+	dm_i2c_reg_write(chip0, ANX9804_PLL_CTRL_REG, 0x07);
+	dm_i2c_reg_write(chip1, ANX9804_PLL_FILTER_CTRL3, 0x19);
+	dm_i2c_reg_write(chip1, ANX9804_PLL_CTRL3, 0xd9);
+	dm_i2c_reg_write(chip1, ANX9804_RST_CTRL2_REG, ANX9804_RST_CTRL2_AC_MODE);
+	dm_i2c_reg_write(chip1, ANX9804_ANALOG_DEBUG_REG1, 0xf0);
+	dm_i2c_reg_write(chip1, ANX9804_ANALOG_DEBUG_REG3, 0x99);
+	dm_i2c_reg_write(chip1, ANX9804_PLL_FILTER_CTRL1, 0x7b);
+	dm_i2c_reg_write(chip0, ANX9804_LINK_DEBUG_REG, 0x30);
+	dm_i2c_reg_write(chip1, ANX9804_PLL_FILTER_CTRL, 0x06);
 
 	/* Force HPD */
-	i2c_reg_write(0x38, ANX9804_SYS_CTRL3_REG,
-		      ANX9804_SYS_CTRL3_F_HPD | ANX9804_SYS_CTRL3_HPD_CTRL);
+	dm_i2c_reg_write(chip0, ANX9804_SYS_CTRL3_REG,
+			 ANX9804_SYS_CTRL3_F_HPD | ANX9804_SYS_CTRL3_HPD_CTRL);
 
 	/* Power up and configure lanes */
-	i2c_reg_write(0x38, ANX9804_ANALOG_POWER_DOWN_REG, 0x00);
-	i2c_reg_write(0x38, ANX9804_TRAINING_LANE0_SET_REG, 0x00);
-	i2c_reg_write(0x38, ANX9804_TRAINING_LANE1_SET_REG, 0x00);
-	i2c_reg_write(0x38, ANX9804_TRAINING_LANE2_SET_REG, 0x00);
-	i2c_reg_write(0x38, ANX9804_TRAINING_LANE3_SET_REG, 0x00);
+	dm_i2c_reg_write(chip0, ANX9804_ANALOG_POWER_DOWN_REG, 0x00);
+	dm_i2c_reg_write(chip0, ANX9804_TRAINING_LANE0_SET_REG, 0x00);
+	dm_i2c_reg_write(chip0, ANX9804_TRAINING_LANE1_SET_REG, 0x00);
+	dm_i2c_reg_write(chip0, ANX9804_TRAINING_LANE2_SET_REG, 0x00);
+	dm_i2c_reg_write(chip0, ANX9804_TRAINING_LANE3_SET_REG, 0x00);
 
 	/* Reset AUX CH */
-	i2c_reg_write(0x39, ANX9804_RST_CTRL2_REG,
-		      ANX9804_RST_CTRL2_AC_MODE | ANX9804_RST_CTRL2_AUX);
-	i2c_reg_write(0x39, ANX9804_RST_CTRL2_REG,
-		      ANX9804_RST_CTRL2_AC_MODE);
+	dm_i2c_reg_write(chip1, ANX9804_RST_CTRL2_REG,
+			 ANX9804_RST_CTRL2_AC_MODE | ANX9804_RST_CTRL2_AUX);
+	dm_i2c_reg_write(chip1, ANX9804_RST_CTRL2_REG,
+			 ANX9804_RST_CTRL2_AC_MODE);
 
 	/* Powerdown audio and some other unused bits */
-	i2c_reg_write(0x39, ANX9804_POWERD_CTRL_REG, ANX9804_POWERD_AUDIO);
-	i2c_reg_write(0x38, ANX9804_HDCP_CONTROL_0_REG, 0x00);
-	i2c_reg_write(0x38, 0xa7, 0x00);
+	dm_i2c_reg_write(chip1, ANX9804_POWERD_CTRL_REG, ANX9804_POWERD_AUDIO);
+	dm_i2c_reg_write(chip0, ANX9804_HDCP_CONTROL_0_REG, 0x00);
+	dm_i2c_reg_write(chip0, 0xa7, 0x00);
 
 	/* Set data-rate / lanes */
-	i2c_reg_write(0x38, ANX9804_LINK_BW_SET_REG, data_rate);
-	i2c_reg_write(0x38, ANX9804_LANE_COUNT_SET_REG, lanes);
+	dm_i2c_reg_write(chip0, ANX9804_LINK_BW_SET_REG, data_rate);
+	dm_i2c_reg_write(chip0, ANX9804_LANE_COUNT_SET_REG, lanes);
 
 	/* Link training */
-	i2c_reg_write(0x38, ANX9804_LINK_TRAINING_CTRL_REG,
-		      ANX9804_LINK_TRAINING_CTRL_EN);
+	dm_i2c_reg_write(chip0, ANX9804_LINK_TRAINING_CTRL_REG,
+			 ANX9804_LINK_TRAINING_CTRL_EN);
 	mdelay(5);
 	for (i = 0; i < 100; i++) {
-		c = i2c_reg_read(0x38, ANX9804_LINK_TRAINING_CTRL_REG);
+		c = dm_i2c_reg_read(chip0, ANX9804_LINK_TRAINING_CTRL_REG);
 		if ((c & 0x01) == 0)
 			break;
 
@@ -118,17 +122,14 @@
 	}
 	if(i == 100) {
 		printf("Error anx9804 link training timeout\n");
-		i2c_set_bus_num(orig_i2c_bus);
 		return;
 	}
 
 	/* Enable */
-	i2c_reg_write(0x39, ANX9804_VID_CTRL1_REG,
-		      ANX9804_VID_CTRL1_VID_EN | ANX9804_VID_CTRL1_EDGE);
+	dm_i2c_reg_write(chip1, ANX9804_VID_CTRL1_REG,
+			 ANX9804_VID_CTRL1_VID_EN | ANX9804_VID_CTRL1_EDGE);
 	/* Force stream valid */
-	i2c_reg_write(0x38, ANX9804_SYS_CTRL3_REG,
-		      ANX9804_SYS_CTRL3_F_HPD | ANX9804_SYS_CTRL3_HPD_CTRL |
-		      ANX9804_SYS_CTRL3_F_VALID | ANX9804_SYS_CTRL3_VALID_CTRL);
-
-	i2c_set_bus_num(orig_i2c_bus);
+	dm_i2c_reg_write(chip0, ANX9804_SYS_CTRL3_REG,
+			 ANX9804_SYS_CTRL3_F_HPD | ANX9804_SYS_CTRL3_HPD_CTRL |
+			 ANX9804_SYS_CTRL3_F_VALID | ANX9804_SYS_CTRL3_VALID_CTRL);
 }
diff --git a/drivers/video/anx9804.h b/drivers/video/anx9804.h
index c0fe3b3..ea6c9f2 100644
--- a/drivers/video/anx9804.h
+++ b/drivers/video/anx9804.h
@@ -16,9 +16,10 @@
 #define ANX9804_DATA_RATE_2700M				0x0a
 
 #ifdef CONFIG_VIDEO_LCD_PANEL_EDP_4_LANE_1620M_VIA_ANX9804
-void anx9804_init(unsigned int i2c_bus, u8 lanes, u8 data_rate, int bpp);
+void anx9804_init(struct udevice *i2c_bus, u8 lanes, u8 data_rate, int bpp);
 #else
-static inline void anx9804_init(unsigned int i2c_bus, u8 lanes, u8 data_rate,
+static inline void anx9804_init(struct udevice *i2c_bus, u8 lanes, u8 data_rate,
 				int bpp) {}
 #endif
+
 #endif
diff --git a/drivers/video/sunxi/sunxi_display.c b/drivers/video/sunxi/sunxi_display.c
index da3e898..5a21f7a 100644
--- a/drivers/video/sunxi/sunxi_display.c
+++ b/drivers/video/sunxi/sunxi_display.c
@@ -901,6 +901,42 @@
 }
 #endif /* CONFIG_VIDEO_LCD_SSD2828 */
 
+#ifdef CONFIG_VIDEO_LCD_PANEL_I2C
+static void sunxi_panel_i2c_init(struct sunxi_display_priv *sunxi_display)
+{
+	const char *name = CONFIG_VIDEO_LCD_PANEL_I2C_NAME;
+	struct udevice *i2c_bus;
+	int ret;
+
+	ret = uclass_get_device_by_name(UCLASS_I2C, name, &i2c_bus);
+	if (ret)
+		return;
+
+	if (IS_ENABLED(CONFIG_VIDEO_LCD_PANEL_EDP_4_LANE_1620M_VIA_ANX9804)) {
+		/*
+		 * The anx9804 needs 1.8V from eldo3, we do this here
+		 * and not via CONFIG_AXP_ELDO3_VOLT from board_init()
+		 * to avoid turning this on when using hdmi output.
+		 */
+		axp_set_eldo(3, 1800);
+		anx9804_init(i2c_bus, 4,
+			     ANX9804_DATA_RATE_1620M,
+			     sunxi_display->depth);
+	}
+	if (IS_ENABLED(CONFIG_VIDEO_LCD_TL059WV5C0)) {
+		struct udevice *chip;
+
+		ret = i2c_get_chip(i2c_bus, 0x5c, 1, &chip);
+		if (ret)
+			return;
+
+		dm_i2c_reg_write(chip, 0x04, 0x42); /* Turn on the LCD */
+	}
+}
+#else
+static void sunxi_panel_i2c_init(struct sunxi_display_priv *sunxi_display) {}
+#endif
+
 static void sunxi_engines_init(void)
 {
 	sunxi_composer_init();
@@ -935,27 +971,12 @@
 		break;
 	case sunxi_monitor_lcd:
 		sunxi_lcdc_panel_enable();
-		if (IS_ENABLED(CONFIG_VIDEO_LCD_PANEL_EDP_4_LANE_1620M_VIA_ANX9804)) {
-			/*
-			 * The anx9804 needs 1.8V from eldo3, we do this here
-			 * and not via CONFIG_AXP_ELDO3_VOLT from board_init()
-			 * to avoid turning this on when using hdmi output.
-			 */
-			axp_set_eldo(3, 1800);
-			anx9804_init(CONFIG_VIDEO_LCD_I2C_BUS, 4,
-				     ANX9804_DATA_RATE_1620M,
-				     sunxi_display->depth);
-		}
 		if (IS_ENABLED(CONFIG_VIDEO_LCD_HITACHI_TX18D42VM)) {
 			mdelay(50); /* Wait for lcd controller power on */
 			hitachi_tx18d42vm_init();
 		}
-		if (IS_ENABLED(CONFIG_VIDEO_LCD_TL059WV5C0)) {
-			unsigned int orig_i2c_bus = i2c_get_bus_num();
-			i2c_set_bus_num(CONFIG_VIDEO_LCD_I2C_BUS);
-			i2c_reg_write(0x5c, 0x04, 0x42); /* Turn on the LCD */
-			i2c_set_bus_num(orig_i2c_bus);
-		}
+		if (IS_ENABLED(CONFIG_VIDEO_LCD_PANEL_I2C))
+			sunxi_panel_i2c_init(sunxi_display);
 		sunxi_composer_mode_set(mode, address, monitor);
 		sunxi_lcdc_tcon0_mode_set(sunxi_display, mode, false);
 		sunxi_composer_enable();